A double side feed type with a press following speed of 1000spm and a single feed type handling up to feed length 110mm are available in a lineup.
The material releasing mechanism using electromagnet driven by inverter doesn't need compressed air. It provides stable release timing and numerical control about pressure for materials.
The controller 470C automatically adjusts the acceleration from the specified feed length and press speed. In addition, the optional unit MP6 enables multi-layer operation. A level meter that monitors the load of the feed motor is also installed as standard.
A dedicated rotation sensor must be installed to synchronize with the press machine. As an option, operation with feed and release press cam signal inputs is possible. The maximum press speed is limited to 300spm if the drive system is based on the synchronous press cam signal specification.
About comparison to other series, please see products guide.
Two movable grips alternately convey the material. It is possible to follow the press rotation speed of 1000 spm.
The maximum material width is 120 mm and the maximum feed length is up to 40 mm.
TG4
Limit of Material
Material Width
8 ～ 120mm
Max. Thickness
0.8mm
Max. Stamp Speed
1000spm
Material Feeding
Method
Grip system by servo motor.
Feed Length
MAX 40.00mm Adjusted by 0.01mm unit.
Feed Acceleration
Automatic calculation *
Material Pressing
Method
Electromagnet
Pressing Capacity
100～1000N Adjusted by 91 step.
Material Releasing Method
Spring
Required Power Supply
Three-phase 200V±10%, 50/60Hz
Product Weight
42kg
* Calculated by the press rotational speed settting and the feed angle setting.
・Feed performance table of TG4 are shown in the table below. Max.feed lengths(mm) under varied speed and feed angles. Details can be confirmed on the feed performance computing form.
It is an NC gripper feeder that can set up to 110 mm maximum feed length (there is one movable grip).Maximum material width is 120 mm, maximum press rotation speed follows up to 600 spm.
We installed a new control that makes grip reciprocation different acceleration. In the case where it is possible to secure a large feed angle, it operates under conditions that material slip is less likely to occur than the conventional machine (GL 110). (patent pended)
G11
Limit of Material
Material Width
8 ～ 120mm
Max. Thickness
0.8mm
Max. Stamp Speed
600spm
Material Feeding
Method
Grip system by servo motor.
Feed Length
MAX 110.00mm Adjusted by 0.01mm unit.
Feed Acceleration
Automatic calculation *
Material Pressing
Method
Electromagnet
Pressing Capacity
100～1000N Adjusted by 91 step.
Material Releasing Method
Spring
Required Power Supply
Three-phase 200V±10%, 50/60Hz
Product Weight
42kg
* Calculated by the press rotational speed settting and the feed angle setting.
・Feed performance table of G11 are shown in the table below. Max.feed lengths(mm) under varied speed and feed angles. Details can be confirmed on the feed performance computing form.
Stamp Speed [spm]
Max. Feed Length [mm]
Feed Angle 150°
Feed Angle 180°
600
1.9
4.5
550
2.9
6.4
500
4.5
9.1
450
6.8
13.0
400
10.4
18.9
350
16.2
28.0
300
25.8
43.1
250
43.1
69.5
200
77.1
110.0
Controller 470C
Explanations on the panel are English only.
Operation panel Description
Indication of servo motor load monitor .
Patent application already.
Clamp open and close switch.
1 Stroke Operation switch.
It can not be operated in this switch alone. Used in conjunction with the "→" switch.
+/-switch.
Run: Push the "+/-" switch while holding down the "1 stroke operation"switch. Feed speed of 1 stroke can be changed.
Set: Change the value of the setting item.
← / → switch.
Run: Inching feed.
Push the "→" switch while holding down the "1 stroke operation"switch, and 1 stroke feeds.
Set: Move to the item to be set change.
Release synchronous operation switch.
Feed synchronous operation switch.
Selector switch, setting mode or operation mode.
Controllers of G Series have same appearance. But each controller is not unusable with the other machine because its own parameters are set. Moreover, it is not compatible with other models.
Display description
Indication of Pressure setting.
Indication of Feed Start setting.
Indication of the Feed Finish angle.
Indication of Overrun CHeck setting.
Indication of Release Start setting.
Indication of SPM setting. ・During the press machine drive ：Indication of the press SPM. ・During the press stop ：Indication of the press machine stop angle.
Indication of Release Finish setting.
Indication of acceleration.
Indication of Feed length setting.
By combining the options of the Data Bank MP6, 99sets of memory settings of Feed Length, Feed Angle, & Release Mode can be saved.You can simplify the setting when exchanging several dies. Please consider it. → See more details.
Two movable grips alternately convey the material. It is possible to follow the press rotation speed of 1000 spm.
The maximum material width is 120 mm and the maximum feed length is up to 40 mm.
TG4
Limit of Material
Max. Width
120mm
Max. Thickness
0.8mm
Max. Stamp Speed
1000spm
Material Feeding
Method
Grip system by servo motor.
Feed Length
MAX 40.00mm Adjusted by 0.01mm unit.
Feed Acceleration
Automatic calculation *
Material Pressing
Method
Electromagnet
Pressing Capacity
100～1000N Adjusted by 91 step.
Material Releasing Method
Spring
Required Power Supply
Three-phase 200V±10%, 50/60Hz
Product Weight
43kg
* Calculated by the press rotational speed settting and the feed angle setting.
・Feed performance table of TG4 are shown in the table below. Max.feed lengths(mm) under varied speed and feed angles. Details can be confirmed on the feed performance computing form.
It is an NC gripper feeder that can set up to 110 mm maximum feed length (there is one movable grip).Maximum material width is 120 mm, maximum press rotation speed follows up to 600 spm.
We installed a new control that makes grip reciprocation different acceleration. In the case where it is possible to secure a large feed angle, it operates under conditions that material slip is less likely to occur than the conventional machine (GL 110). (patent pended)
G11
Limit of Material
Max. Width
8 ～ 120mm
Max. Thickness
0.8mm
Max. Stamp Speed
600spm
Material Feeding
Method
Grip system by servo motor.
Feed Length
MAX 110.00mm Adjusted by 0.01mm unit.
Feed Acceleration
Automatic calculation *
Material Pressing
Method
Electromagnet
Pressing Capacity
100～1000N Adjusted by 91 step.
Material Releasing Method
Spring
Required Power Supply
Three-phase 200V±10%, 50/60Hz
Product Weight
42kg
* Calculated by the press rotational speed settting and the feed angle setting.
・Feed performance table of G11 are shown in the table below. Max.feed lengths(mm) under varied speed and feed angles. Details can be confirmed on the feed performance computing form.
It can not be operated in this switch alone. Used in conjunction with the "→" switch.
+/-switch.
Run: Push the "+/-" switch while holding down the "1 stroke operation"switch. Feed speed of 1 stroke can be changed.
Set: Change the value of the setting item.
← / → switch.
Run: Inching feed.
Push the "→" switch while holding down the "1 stroke operation"switch, and 1 stroke feeds.
Set: Move to the item to be set change.
Release synchronous operation switch.
Feed synchronous operation switch.
Selector switch, setting mode or operation mode.
Controllers of G Series have same appearance. But each controller is not unusable with the other machine because its own parameters are set. Moreover, it is not compatible with other models.
Display description
Indication of Pressure setting.
Indication of Feed Start setting.
Indication of the Feed Finish angle.
Indication of Overrun CHeck setting.
Indication of Release Start setting.
Indication of SPM setting. ・During the press machine drive ：Indication of the press SPM. ・During the press stop ：Indication of the press machine stop angle.
Indication of Release Finish setting.
Indication of acceleration.
Indication of Feed length setting.
By combining the options of the Data Bank MP6, 99sets of memory settings of Feed Length, Feed Angle, & Release Mode can be saved.You can simplify the setting when exchanging several dies. Please consider it. → See more details.
It can not be operated in this switch alone. Used in conjunction with the "→" switch.
+/-switch.
Run: Push the "+/-" switch while holding down the "1 stroke operation"switch. Feed speed of 1 stroke can be changed.
Set: Change the value of the setting item.
← / → switch.
Run: Inching feed.
Push the "→" switch while holding down the "1 stroke operation"switch, and 1 stroke feeds.
Set: Move to the item to be set change.
Release synchronous operation switch.
Feed synchronous operation switch.
Selector switch, setting mode or operation mode.
Controllers of G Series have same appearance. But each controller is not unusable with the other machine because its own parameters are set. Moreover, it is not compatible with other models.
Display description
Indication of Pressure setting.
Indication of Feed Start setting.
Indication of the Feed Finish angle.
Indication of Overrun CHeck setting.
Indication of Release Start setting.
Indication of SPM setting. ・During the press machine drive ：Indication of the press SPM. ・During the press stop ：Indication of the press machine stop angle.
Indication of Release Finish setting.
Indication of acceleration.
Indication of Feed length setting.
By combining the options of the Data Bank MP6, 99sets of memory settings of Feed Length, Feed Angle, & Release Mode can be saved.You can simplify the setting when exchanging several dies. Please consider it. → See more details.
