High-Speed NC Roll Feeder : H Series

It's a high-end model with press following speed of 1,000 spm.

The material releasing mechanism using electromagnet driven by inverter doesn't need compressed air. It provides stable release timing and numerical control about pressure for materials.

New control unit automatically adjusts feed acceleration by specified feed langth and press stamping speed. And it provides multi layer operation with option unit MP6. A level meter for monitoring the load of the feed motor is also installed.


3 models are presented for various material width and thickness.

Model NameLimit of MatrialMax. Stamp Speed
[spm]
Max. Width
[mm]
Max. Thickness
[mm]
H07751.21000
H131301.6
H25250700

An original encoder is required to install for synchronization with stamping. As an optional function, feeder can accept feed and release signals to synchronize press machine. Maximum stamp speed is limited 300spm on this function.


About comparison to other series, please see the other page.

H07

H07.jpg

Compact model for high speed which was downsized while maintaining maximum following speed of H13. It corresponds to material width 75 mm and thickness 1.2 mm. Refer to the table below for basic specifications.

H07
Limit of MatrialMax. Width75mm
Max. Thickness1.2mm
Max. Stamp Speed1000spm
Material FeedingMethodRoller + Servomotor
Feed Length999.99mm Max.
Adjusted by 0.01mm unit.
Feed AccelerationAutomatic calculation *1
Repeatability±0.05mm *2
Material PressingMethodSolenoid *3
Pressing Capacity0~1500N
Adjusted by 101 step.
Material Releasing MethodSolenoid
Required Power SupplyThree-phase 200V±10% 50/60Hz
Product Weight34kg
*1 Calculated by the press rotational speed settting and the feed angle setting.
*2 Condition: Feed length 50 mm · No release.
*3 Spring is used in combination to prevent material falling off when the power is off.

・Feed performance table of H07 are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details of performance can be calculated on this page.

Stamp Speed
[spm]
Max. Feed Length [mm]
Feed Angle
180°
Feed Angle
210°
10005 *9 *
9008 *13 *
8001118 *
7001725
6002538
5004159
4006890
300113143
200203248

*1 Depending on the starting angle and acceleration of the press machine, the release operation may not be able to follow up.

H13

H13.jpg

H13 is a high speed roll feeder capable of following speeds up to 1000 spm. The width of max130mm , the material thickness corresponds to the max 1.6mm. For other basic specifications please refer to the table below.

H13
Limit of MatrialMax. Width130mm
Max. Thickness1.6mm
Max. Stamp Speed1000spm
Material FeedingMethodRoller + Servomotor
Feed Length999.99mm Max.
Adjusted by 0.01mm unit.
Feed AccelerationAutomatic calculation *1

Repeatability

±0.05mm *2
Material PressingMethodSolenoid *3
Pressing Capacity0~2500N
Adjusted by 101 step.
Material Releasing MethodSolenoid
Required Power SupplyThree-phase 200V±10% 50/60Hz
Product Weight52kg
*1 Calculated by the press rotational speed settting and the feed angle setting.
*2 Condition: Feed length 50 mm · No release.
*3 Spring is used in combination to prevent material falling off when the power is off.

・Feed performance table of H13 are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details of performance can be calculated on this page.

Stamp Speed
[spm]
Max. Feed Length [mm]
Feed Angle
180°
Feed Angle
210°
10005 *8 *
9007 *11 *
8001016 *
7001523
6002334
5003653
4006386
300110142
200206254

*1 Depending on the starting angle and acceleration of the press machine, the release operation may not be able to follow up.

H25

H25.jpg

H25 is a high speed roll feeder capable of following speeds up to 700 spm. The width of max 250mm, the material thickness corresponds to the max 1.6mm. For other basic specifications, refer to the table below.

H25
Limit of MatrialMax. Width250mm
Max. Thickness1.6mm
Max. Stamp Speed700spm
Material FeedingMethodRoller + Servomotor
Feed Length999.99mm Max.
Adjusted by 0.01mm unit.
Feed AccelerationAutomatic calculation *1

Repeatability

±0.05mm *2
Material PressingMethodSolenoid *3
Pressing Capacity0~2500N
Adjusted by 101 step.
Material Releasing MethodSolenoid
Required Power SupplyThree-phase 200V±10% 50/60Hz
Product Weight66kg
*1 Calculated by the press rotational speed settting and the feed angle setting.
*2 Condition: Feed length 50 mm · No release.
*3 Spring is used in combination to prevent material falling off when the power is off.

・Feed performance table of H25 are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details of performance can be calculated on this page.

Stamp Speed
[spm]
Max. Feed Length [mm]
Feed Angle
180°
Feed Angle
210°
7001117 *
6001725
5002740
4004768
30091123
200187235

*1 Depending on the starting angle and acceleration of the press machine, the release operation may not be able to follow up.

RV specification

H25-RV2.jpg

It is an option that removes apron bracket by cam lever. The feed roll can be easily inspected and cleaned.

Separate roll options are now available.

The photo on the left shows the state that apron bracket is removed (separate roll equipment).


You can see the movie of detachment of apron bracket.
※ The movie is the old product of the same specification, HS130B.
Click screen and the movie will start. It has sounds, so please be attentive to volume.

Controller 430C

Explanations in the panel are English only.

Display description

430_CNT_DISP.png
  1. Indication of Pressure setting.
  2. Indication of Feed Start setting.
  3. Indication of the Feed Finish angle.
  4. Indication of Overrun CHeck setting.
  5. Indication of Release Start setting.
  6. Indication of SPM setting.
    ・During the press machine drive :Indication of the press SPM.
    ・During the press stop :Indication of the press machine stop angle.
  7. Indication of Release Finish setting.
  8. Indication of acceleration.

Operation panel Description

430_CNT_PANEL.png
  1. Indication of Feed Length setting.
  2. Indication of servo motor load monitor .
    • Patent application already.
  3. Roll open and close switch.
    • Set: Change the value of the setting item.
  4. 1 Stroke Operation switch.
    • It can not be operated in this switch alone. Used in conjunction with the "→" switch.
  5. +/-switch.
    • Run: Push the "+/-" switch while holding down the "1 stroke operation"switch. Feed speed of 1 stroke can be changed.
    • Set: Change the value of the setting item.
  6. Release synchronous operation switch.
  7. Feed synchronous operation switch.
  8. Selector switch, setting mode or operation mode.

Controllers of H Series have same appearance. But each controller is not unusable with the other machine because its own parameters are set. Moreover, it is not compatible with other models.


By combining the options of the Data Bank MP6, 99sets of memory settings of Feed Length, Feed Angle, & Release Mode can be saved.You can simplify the setting when exchanging several dies. Please consider it. → See more details

Infomation

2017/2/23

Added single output mode of work shortage sensor signal.
Please check the contents from here.

02.SEP.2016

We have started selling H series.