Compact NC Roll Feeding Machine : J Series
The model whose release mechanism is based on fast response air diaphragm. Maximum stamp speed is 300spm and material width is up to 2.3mm. 3 models are presented for various width and thickness.
New control unit automatically adjusts feed acceleration by specified feed langth and press stamping speed. And a level meter for monitoring the load of the feed motor is also installed. In addition, "high acceleration type" and "10-times feed length" as options in the previous model RF-A series are normally installed.
Model Name | Limit of Matrial | Max. Stamp Speed [spm] |
---|
Max. Width [mm] | Max. Thickness [mm] |
J06 | 70 | 1.2 | 300 |
---|
J15 | 150 | 2.3 | 250 |
---|
J25 | 250 |
---|
For installation, two signals for synchronization with stamping and air supply are required.
We have options available as needed, so please check.
About comparison to other series, please see products Guide.
For faster stamp speed, we suggest H Series. R series can handle the thinkness up to 3.2mm. And to deal with short material, T series is also suggested.
J06
The smallest model in our feeders. Maximum material width is 70mm and the thickness is 1.2mm. The table below shows basic specifications.
| J06 |
---|
Limit of Matrial | Max. Width | 70mm |
---|
Max. Thickness | 1.2mm |
---|
Max. Stamp Speed | 300spm |
---|
Material Feeding | Method | Roller + Servomotor |
---|
Feed Length | MAX 9999.99mm Adjusted by 0.01mm unit. |
---|
Feed Speed | Automatic calculation * |
---|
Material Pressing | Method | Spring |
---|
Pressing Capacity | MAX 785N Adjusted by screws. |
---|
Material Releasing Method | Air diaphragm cylinder |
---|
Required Power Supply | Three phase or single phase , 50/60Hz |
---|
Product Weight | 13kg |
---|
* Calculated by the press rotational speed settting and the feed angle setting.
Feed performance table of J06 are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details can be confirmed on the feed performance computing form
.
Stamp Speed [spm] | Max. Feed Length [mm] |
---|
Feed Angle 150° | Feed Angle 180° | Feed Angle 210° |
300 | 12 | 19 | 27 |
---|
260 | 17 | 26 | 38 |
---|
220 | 25 | 39 | 56 |
---|
180 | 41 | 62 | 87 |
---|
140 | 72 | 108 | 150 |
---|
J15 / J25
Two models whose limit of material width is 2.3mm are presented for various material width.
| J15 | J25 |
---|
Limit of Matrial | Max. Width | 150mm | 250mm |
---|
Max. Thickness | 2.3mm |
---|
Max. Stamp Speed | 250spm |
---|
Material Feeding | Method | Roller + Servomotor |
---|
Feed Length | MAX 9999.99mm Adjusted by 0.01mm unit. |
---|
Feed Speed | Automatic calculation * |
---|
Standard Load Width / Thickness | 150/1.6mm 60/2.3mm | 250/1.2mm 150/1.6mm 60/2.3mm |
---|
Material Pressing | Method | Spring |
---|
Pressing Capacity | MAX 1470N Adjusted by screws. |
---|
Material Releasing Method | Air diaphragm cylinder |
---|
Required Power Supply | Three phase or single phase , 50/60Hz |
---|
Product Weight | 25kg | 28kg |
---|
* Calculated by the press rotational speed settting and the feed angle setting.
Feed performance table of J15 and J25 are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details can be confirmed on the feed performance computing form
.
Stamp Speed [spm] | Max. Feed Length [mm] |
---|
Feed Angle 150° | Feed Angle 180° | Feed Angle 210° |
250 | 18 | 29 | 41 |
---|
220 | 25 | 39 | 55 |
---|
190 | 36 | 54 | 76 |
---|
160 | 53 | 79 | 111 |
---|
130 | 84 | 125 | 174 |
---|
Controller 410C
Explanations in the panel are English only.
- Indication of Feed Length setting.
- Indication of Feed Angle setting.
- Continuous press operation display of the angle used for feeding during .
- Selector switch, setting mode or operation mode.
- Feed synchronous operation switch.
- Release synchronous operation switch.
- Indication of spm setting.
- Continuous press operation :Actual press spm display.
- ← / → switch.
- Run: Inching feed.
- Push the "→" switch while holding down the "1 stroke operation"switch, and 1 stroke feeds.
- Set: Move to the item to be set change.
- +/-switch.
- Run: Push the "+" switch while holding down the "1 stroke operation"switch. Feed speed of 1 stroke can be changed.
- Set: Change the value of the setting item.
- 1 Stroke Operation switch
- It can not be operated in this switch alone. Used in conjunction with the "→" switch.
- Roll open and close switch.
- Indication of servo motor load monitor .
- Patent application already.
Controllers of J Series have same appearance. But each controller is not unusable with the other machine because its own parameters are set. Moreover, it is not compatible with other models.
Information
2018/10/01
The setting method of the release mode of J series, R series, and T series will be changed.
another page
2017/2/23
Added single output mode of work shortage sensor signal.
Please check the contents from here.