NC Twin Roll Feeder : T Series
This series is designed for short materials. Two feeders placed on the left and right sides of the die, feed and draw material. The compact model TJ06 and TJ15 are newly lineuped.
The main body and controller unit are integrated and it saves space. With a sliding plates as standard, the machine position is possible to adjust to the inside or outside of a bolster (by manual operation).
New control unit automatically adjusts feed acceleration by specified feed langth and press stamping speed. And a level meter for monitoring the load of the feed motor is also installed.
4 models are provided for vary material width.
Model Name | Limit of Matrial | Max. Stamp Speed [spm] |
---|
Max. Width [mm] | Max. Thickness [mm] |
T20 | 200 | 3.2 | 200 |
---|
T30 | 300 |
---|
TJ06 | 70 | 1.2 | 200 |
---|
TJ15 | 150 | 2.3 | 200 |
---|
For installation, two signals for synchronization with stamping and air supply are required.Please check whether the length of material to be used reaches enough between the rollers of the left and right main body.
T20 / T30
In the model of 3.2mm maximum material thickness, you can choose from two types of width.
T20 / T30 is equipped with a C-type frame. workpiece can be supplied from the machine front.
For basic specification, prease refer below table.
| T20 | T30 |
---|
Limit of Matrial | Max. Width | 200mm | 300mm |
---|
Max. Thickness | 3.2mm |
---|
Max. Stamp Speed | 200spm |
---|
Material Feeding | Method | Roller + Servomotor |
---|
Feed Length | 999.99mm Max. Adjusted by 0.01mm unit. |
---|
Feed Speed | Automatic calculation * |
---|
Standard Load Width / Thickness Coil Mode | 50/3.2mm 200/1.6mm | 50/3.2mm 300/1.6mm |
---|
Standard Load Width / Thickness Sheet Mode | 200/3.2mm MAX Feeding material weight 15kg | 300/3.2mm MAX Feeding material weight 15kg |
---|
Material Pressing | Method | Spring |
---|
Pressing Capacity | 1716N Adjusted by screws. |
---|
Material Releasing Method | Air Cylinder |
---|
Sheet Mode | Press shoot count | MAX 999 1 unit setting |
Discharge Length | MAX999mm 1mm unit setting |
Required Power Supply | Three phase 200V±10%, 50/60Hz |
---|
Product Weight | Feed side (with controller)48kg Pull side 46kg | Feed side (with controller)56kg Pull side 54kg |
---|
* Calculated by the press rotational speed settting and the feed angle setting.
・Feed performance table of T series are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details can be confirmed on the feed performance computing form
.
Stamp Speed [spm] | Max. Feed Length [mm] |
---|
Feed Angle 180° | Feed Angle 210° |
200 | 22 | 31 |
---|
180 | 28 | 39 |
---|
160 | 36 | 51 |
---|
140 | 48 | 68 |
---|
120 | 68 | 94 |
---|
100 | 100 | 138 |
---|
80 | 160 | 221 |
---|
60 | 283 | 367 |
---|
40 | 534 | 659 |
---|
The lower movies are about this product utilized for processing short materials. Click screen and the movie will start. It has sounds, so please be attentive to volume.
※The video is TRF202 of the old model of the same spec.
About comparison to other series, please see the other page.
TJ06
Maximum material width is 70mm and the thickness is 1.2mm. Material supply from the front of the main body is not available.The table below shows basic specifications.
| TJ06 |
---|
Limit of Matrial | Max. Width | 70mm |
---|
Max. Thickness | 1.2mm |
---|
Max. Stamp Speed | 200spm |
---|
Material Feeding | Method | Roller + Servomotor |
---|
Feed Length | 最大9999.99mm Adjusted by 0.01mm unit. |
---|
Feed Speed | Automatic calculation * |
---|
Standard Load Width / Thickness Coil Mode | 70/1.2mm |
---|
Standard Load Width / Thickness Sheet Mode | 70/1.2mm MAX Feeding material weight 3kg |
---|
Material Pressing | Method | Spring |
---|
Pressing Capacity | MAX 785N Adjusted by screws. |
---|
Material Releasing Method | Air diaphragm cylinder |
---|
Sheet Mode | Press shoot count | MAX 999 1 unit setting |
Discharge Length | MAX999mm 1mm unit setting |
Required Power Supply | Three phase 200V±10%, 50/60Hz |
---|
Product Weight | Feed side (with controller)15kg Pull side 11kg |
---|
* Calculated by the press rotational speed settting and the feed angle setting.
・Feed performance table of TJ06 are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details can be confirmed on the feed performance computing form
.
Stamp Speed [spm] | Max. Feed Length [mm] |
---|
Feed Angle 180° | Feed Angle 210° |
200 | 31 | 45 |
---|
180 | 40 | 56 |
---|
160 | 52 | 73 |
---|
140 | 70 | 97 |
---|
120 | 97 | 136 |
---|
100 | 144 | 200 |
---|
80 | 231 | 318 |
---|
60 | 408 | 528 |
---|
40 | 769 | 949 |
---|
TJ15
Maximum material width is 150mm and the thickness is 2.3mm. Material supply from the front of the main body is not available.The table below shows basic specifications.
| TJ15 |
---|
Limit of Matrial | Max. Width | 150mm |
---|
Max. Thickness | 2.3mm |
---|
Max. Stamp Speed | 200spm |
---|
Material Feeding | Method | Roller + Servomotor |
---|
Feed Length | 999.99mm Max. Adjusted by 0.01mm unit. |
---|
Feed Speed | Automatic calculation * |
---|
Standard Load Width / Thickness Coil Mode | 150/1.6mm 60/2.3mm |
---|
Standard Load Width / Thickness Sheet Mode | 150/2.3mm MAX Feeding material weight 10kg |
---|
Material Pressing | Method | Spring |
---|
Pressing Capacity | MAX 1470N Adjusted by screws. |
---|
Material Releasing Method | Air diaphragm cylinder |
---|
Sheet Mode | Press shoot count | MAX 999 1 unit setting |
Discharge Length | MAX999mm 1mm unit setting |
Required Power Supply | Three phase 200V±10%, 50/60Hz |
---|
Product Weight | Feed side (with controller) 25kg Pull side 23kg |
---|
* Calculated by the press rotational speed settting and the feed angle setting.
・Feed performance table of TJ15 are shown in the table below.
Max.feed lengths(mm) under varied speed and feed angles.
Details can be confirmed on the feed performance computing form
.
Stamp Speed [spm] | Max. Feed Length [mm] |
---|
Feed Angle 180° | Feed Angle 210° |
200 | 31 | 44 |
---|
180 | 39 | 56 |
---|
160 | 51 | 72 |
---|
140 | 69 | 96 |
---|
120 | 96 | 134 |
---|
100 | 142 | 197 |
---|
80 | 228 | 314 |
---|
60 | 403 | 522 |
---|
40 | 760 | 939 |
---|
Controller 450C
Two types of mode, sheet mode and coil mode can be selected.
Sheet Mode
- Left Feed Length(mm)
- Press Shot Count
- Handover Point
- Ejection Length(mm)
- Light Feed Length(mm)
- Release Mode
- Overlap
- SPM
- Feed Angle
Coil Mode
- Indicator of Feed Length. / Feed side
- Indicator of coil mode
- Operation status indication in coil mode.
- Indicator of Feed Length. / Pulling side
- Release Mode
- SPM
- Feed Angle
By combining the options of the Data Bank MP6, 99sets of memory settings of Feed Length, Feed Angle, & Release Mode can be saved.You can simplify the setting when exchanging several dies. Please consider it. → See more details.
Infomation
2018/10/01
The setting method of the release mode of J series, R series, and T series will be changed.
another page
2017/2/23
Added single output mode of work shortage sensor signal.
Please check the contents from here.
01.NOV.2016
We have started selling T series.